I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*: Formbot Voron V0.1 Kit (AliExpress) https://bit.ly/39kfWdC LDO Voron V0.1 KIT (Caribou3D) https://bit.ly/3KBxqzL Recommended Kits for bigger DIY printers: Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE Voron Trident Kit (AliExpress) https://bit.ly/3yxMaNe STL files, instructions and BOM on the recent upgrades: https://247printing.gumroad.com/l/247zeroBeta1 Support my work at Patreon: https://www.patreon.com/247printing My Instagram and Twitter - more about my doings and behind the scenes: Instagram: https://www.instagram.com/247printing/ Twitter: https://twitter.com/247_printing Watch the print at 1100mm/s:    • Shorts   💚Pizza, Beer and Coffee helps me going on💚 https://paypal.me/247printing 💚Thanks to all who support/ed my work💚 ---------------Settings: Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing https://amzn.to/3Bi0x7k T_Hotend = 290C T_Bed = 90C Requested Speed: 1000mm/s Acceleration: 35.000 mm/s² square_corner_velocity: 15mm/s Nozzle: 0.4mm Layer Height: 0.1mm Line width: 0.4mm Volumetric flow: 40mm³/s Lengths of straights: 65mm Lengths of printing @ REAL 1000mm/s: 35mm Xxxx ALL DESIGNS AVAILABLE SOON xxxX @ Voron Users / Thingiverse ******UPGRADES STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming: For years now, I use BigTreeTech/BIQU products - very much recommended: (I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor) Get the Octopus Board here: https://bit.ly/31kKCrj —MOTION (Part 1: Video Deep Dive incoming) Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S) https://amzn.to/3kBO5tm F623 bearings instead of toothed idlers https://amzn.to/2UktSgZ WD40 specialist dry lubricant for rails (PTFE) https://amzn.to/3ziGaF4 Gates-LL-2GT 6mm belts https://amzn.to/3kCaAht — EXTRUSION: (Part 2: Video Deep Dive) Slice Engineering Mosquito Magnum (5% off!): https://www.sliceengineering.com/?p=rkjO5IsbY VolcoMosq Block (+9mm melt): https://www.youtube.com/watch?v=_2xph8QkcpU E3D Hemera (Bowden config) https://amzn.to/3zdvAzk Capricorn Bowden Tube https://amzn.to/3kBrgWE 50W heater (24V) https://amzn.to/2UmOIwa PT1000 temp sensor https://amzn.to/3ivfdY2 Boron Nitride Paste @ heater, thermistor and heat break https://amzn.to/3kvPem6 — COOLING (Part 3: Video Deep Dive) 4010 blower fans (24V), updated toolhead https://amzn.to/3irazKT optimized air ducts for part cooling with aluminium tape insulation https://amzn.to/3zhbuEs External Static Cooling: 4x4020 fans (24V) https://amzn.to/3zcap0D 4x40mm heatsink at AB stepper motors https://amzn.to/3irvLAh 2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors) https://amzn.to/3wOmfMJ 25mm axial fan (5V) for stepper drivers https://amzn.to/3eDf4AW — Software / Firmware / Controllers (Part 4: Video Deep Dive): Klipper https://www.klipper3d.org/ Raspberry Pi Zero W (Mainsail) https://amzn.to/3xR9l21 Raspberry Pi 3B (Input Shaping and Octoprint) https://amzn.to/2UwIMAu Alternative: Raspberry Pi4: https://amzn.to/3kBt4io Simplify 3D: multi processes used https://www.simplify3d.com/ ------------------------------------------------------- My modest video gear*: iPhone 11 Pro: https://amzn.to/2VZYswJ Smartphone video rig: https://amzn.to/3iriub5 GoPro Hero 9: https://amzn.to/2UZI9Q5 FLIR ONE PRO: https://amzn.to/2UWAe67 Similar to the soft boxes I use: https://amzn.to/3xRes2d Similar to the tripod I use: https://amzn.to/2V1I6mw *Amazon links are affiliate links at no extra costs for you! #JoinTheSpeed #247printing #volcomosq #SpeedBoatRace